Products by Type

Vertical Immersion Pumps
Process Duty PumpsStandard End-Suction PumpsSealless PumpsSelf-Priming Centrifugal PumpsMulti-stage PumpsDiaphragm PumpsVertical Immersion PumpsDouble Suction PumpsVertical Turbine PumpsRegenerative Turbine PumpsIn-line Centrifugal PumpsSubmersible Centrifugal PumpsSlurry PumpsSubmersible Turbine PumpsHand Operated PumpsShaft Sealing ProductsMixing EquipmentControls & AccessoriesProgressive Cavity PumpsMetering PumpsRotary Gear/Vane PumpsSanitary Pumps

Series 600 Vertical Process Pumps

VERTIFLO SERIES 600 VERTICAL PROCESS PUMPS

Typical Applications:

  • Industrial Spray Washers
  • Pickling/Bonderizing
  • Spray Booths
  • Coolant Systems
  • Paint Systems
  • Filtration Systems
  • Pollution Control
  • E-Coat Paint Systems

Performance:

  • Capacities to 3000 GPM
  • Heads to 230 Feet
  • Temperature to 180° F
  • Column Extensions of 12", 15" & 21"

Construction:

  • Cast Iron
  • 316 Stainless Steel Fitted
  • 316 Stainless Steel
  • Alloy 20

Series 700 Vertical Non-Clog Pumps

VERTIFLO SERIES 700 VERTICAL NON-CLOG PUMPS

Typical Applications:

  • Industrial Wastes
  • Sanitary Wastes
  • Process Wastes
  • Rendering Wastes
  • Pollution Control

Performance:

  • Capacities to 1500 GPM
  • Heads to 100 Feet
  • Pit Depths to 26 Feet

Construction:

  • Cast Iron

Series 800 Vertical Sump Pumps

VERTIFLO SERIES 800 VERTICAL SUMP PUMPS

Typical Applications:

  • Industrial Process
  • Pollution Control
  • Sump Drainage
  • Hazardous, Toxic & Inflammable Liquids
  • Cooling Towers
  • Acids
  • Clear Liquids
  • Flood Control
  • Corrosive Liquids
  • Condensate

Performance:

  • Capacities to 3000 GPM
  • Heads to 230 Feet TDH
  • Temperature to 350° F
  • Pit Depths to 26 Feet

Construction:

  • Cast Iron
  • 316 Stainless Steel Fitted
  • All 316 Stainless Steel
  • Alloy 20
  • Hastelloy
  • CD4MCu

Series 900 Vertical Vortex Pumps

VERTIFLO SERIES 900 VERTICAL VORTEX PUMPS

Typical Applications:

  • Chemical Slurries
  • Fragile Food Processing Solids
  • Paper & Pulpy Solids
  • Petroleum
  • Oils
  • Sewage & Waste treatment
  • Textiles

Performance:

  • Capacities to 1600 GPM
  • Heads to 170 Feet TDH
  • Temerature to 350° F
  • Pit Depths to 26 feet

Construction:

  • Cast Iron
  • 316 Stainless Steel Fitted
  • All 316 Stainless Steel
  • Alloy 20
  • CD4MCu

Series 1100 Vertical Cantilever Vortex Pumps

VERTIFLO SERIES 1100 VERTICAL CANTILEVER VORTEX PUMP

Typical Applications:

  • Fines and Slurry
  • Solids Pumping and Sump Drainage
  • Flood Control
  • Process Drainage
  • Corrosive Chemicals and Hazardous Liquids
  • Waste Paper Stock
  • Clay and Water
  • Iron Ore Slurry
  • Black Liquor

Performance:

  • Capacities to 1600 GPM
  • Heads to 170 Feet
  • Temperature to 400° F
  • Pump Length to 6 Feet
  • Semi-open Impeller with External Adjustment
  • Shaft Diameter to 5"

Construction:

  • Cast Iron
  • 316 Stainless Steel Fitted
  • Alloy 20
  • 27% Chrome Iron
  • Hastelloy
  • CD4MCu

Series 1200 Vertical Cantilever Pumps

VERTIFLO SERIES 1200 VERTICAL CANTILEVER PUMPS

Typical Applications:

  • Industrial Process
  • Corrosive Liquids
  • Paint
  • Waste Water
  • Chemical Slurries

Performance:

  • Capacities to 3000 GPM
  • Heads to 230 Feet
  • Temperature to 400° F
  • Pump Length to 6 Feet
  • Shaft Diameter to 5"

Construction:

  • Cast Iron
  • 316 Stainless Steel
  • Alloy 20
  • Hastelloy
  • CD4MCu

3171 Vertical Sump Pumps

3171 Vertical Sump Pumps - The Goulds model 3171 is the veteran vertical sump and process pump.  Thousands of installations in industrial process, sump drainage, corrosive liquids, pollution control, molten salts and others attest to the 3171's remarkable performance.

CV3171 Vortex Type Vertical Sump Pumps

CV3171 Vortex Type Vertical Sump Pumps - The CV3171 is a recessed impeller (except LF 1x1.5-8), circular volute type sump pump.  Ideal for services involving large solids and shear sensitive fluids.  Circular volute minimizes radial loads making this the ideal pump for low flow and/or solids handling process applications.

NM3171 Non-metallic Vertical Sump Pumps

NM3171 Non-metallic Vertical Sump Pumps - Designed for severe corrosive applications.  Casings and impellers are interchangeable with model NM3196.  Cost-effective alternative to high alloy construction.

VJC/5150 Vertical Sump Pumps

VJC/5150 Vertical Sump Pumps - Heavy duty vertical cantilever type pumps for the most abrasive services.

VHS Vertical Sump Pumps

VHS Vertical Sump Pumps - Heavy duty vertical cantilever pumps designed to handle large/fibrous solids.

AMT industrial sump pumps

The AMT line of Industrial/Commercial Sump pumps is designed for heavy duty commercial applications, as well as residential use where a combination of durability and high performance is required. AMT Sump pumps are available in stainless steel, bronze and cast iron constructions with TEFC motors in 1/3 through 3/4 HP for proper pump selection in most applications. All models include stainless steel shaft, screen and float. All motors are fitted with automatic switch and an 8 foot 16/3 115 VAC line cord. Pumps require minimum sump pit of 14″ diameter and 24″ depth.

• Stainless Steel, Bronze and Cast Iron Construction
• Stainless Steel Shaft & Float
• Carbon Bearings
• 29” to 44” Column Height
• 1-1/2” or 2” NPT Discharge
• Maximum Head 30 Ft.
• Maximum Flow 103 GPM
• Semi-Open, Clog Resistant Impellers
• Available with Totally Enclosed Fan Cooled (TEFC) 1/3, 1/2 and 3/4 HP 115 VAC, Single Phase Motors

AMT bronze coolant pump

The AMT Bronze Coolant/Recirculating pump has been manufactured for a wide variety of Industrial/Commercial Coolant and Recirculating applications. The absence of a bottom bearing makes the unit ideal for handling erosive liquids. A 36″ 3-conductor
power cord is included. NOTE: The motor on this pump is not intended to be submerged in liquid. The liquid level should always be at least 2″ below motor bottom. (Maximum depth of liquid is 6″.)
• Cast Bronze Construction
• No Bottom Bearing!!!
• Brass Column and Impeller Shaft
• Bronze Self-Cleaning Open Impeller
• 3/8˝ NPT Discharge Port
• Fiber Gasket
• Maximum Temperature 200° F
• Maximum Flow 8 GPM
• Maximum Head 10 Ft.
• Available with 115 VAC Single Phase or 230 VAC Single Phase Motors, 1590 RPM
• 1/25 HP Totally Enclosed Fan Cooled (TEFC) Motor

AMT heavy duty coolant pumps

The AMT Heavy Duty Industrial Coolant pump has been designed for a broad range of Industrial/Commercial coolant and recirculating applications. Back vanes on the impellers of models 4421-95 through 4443-95 balance pressure and thereby eliminate the need for mechanical seals. All models with extended shafts are fitted with aligning coupling between motor and shaft. Dual volute construction of models 4421-95 through 4443-95 eliminates radial thrust and therefore the need for bottom bearings. A Universal mounting bracket system is included with these pumps (see below). AMT Mounting Brackets (Included): Models 4410-90 & 4420-90 mounting brackets are designed to simplify the pump installation/removal process and expand the application range for each pump in the line. With the bracket system, it is no longer necessary to disassemble motor from pump end for installation and removal. Simply unfasten the brackets from the tank cover and insert or remove the complete pump. The bracket system also controls the immersion depth of each pump in the line by clamping to the pump column at the most desirable position.

• Cast Iron Casing and Column
• 3/4˝ to 1-1/2˝ NPT Discharge Port
• Includes Universal Mounting Bracket
• Dual Volute Design Reduces Radial Load on Motor – NO BOTTOM BEARING!
• Maximum Temperature 200° F
• Maximum Flow 67 GPM
• Maximum Head 32 Ft.
• Self-Cleaning, Semi-Open Stainless Steel Impeller
• Available with Single or Three Phase 56C Motor
• 1/8 to 3/4 HP Totally Enclosed Fan Cooled (TEFC) Motor, 1725 RPM

AMT immersion/suction coolant pumps

AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps are available with a stainless steel impeller for added corrosion/erosion resistance and durability. 1/8 & 1/4 HP models are available in 115/230 VAC, 60 Hz single phase and 230/460 VAC, 50/60 Hz three phase. Motors are Totally Enclosed with sealed bearings and operate at 3450 RPM. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.

• Fully Interchangeable with Units Furnished on Most Imported Machine Tools
• 1/8 to 1 HP Totally Enclosed Motors
• 2 Pole, 3450 RPM
• Single or Three Phase Motors
• Stainless Steel Semi-Open Impeller
• Cast Iron Construction
• Maximum Temperature 180° F
• Maximum Flow 56 GPM (Water)
• Maximum Head 60 Ft. (Water)

AMT vertical sprayer/washer pumps

AMT Vertical Sealless Sprayer/ Washer pumps are designed for OEM, automotive and industrial washing machines, parts cleaners, spray booths and cooling towers. “No bottom bearing” design and stainless steel impeller resists errosion from abrasives and ensures a long, maintenance free life for the pump. CNC machined stainless steel pump shafts. Built-in stainless steel suction screen protects pump from clogging and damage caused by large solids. Heavy duty universal mounting plates permit easy installation into existing tanks, booths, equipment, etc.

• Cast Iron Construction with 300 Series Investment Cast Stainless Steel Impeller
• Stainless Steel Pump Shaft
• No Bottom Bearing!
• Dual Volute Design Reduces Radial Load on Motor
• Maximum Temperature 200° F
• Maximum Flow 140 GPM
• Maximum Head 140 Ft. (61 PSI)
• Stainless Steel Suction Screen
• Includes Heavy Duty Universal Mounting Plates
• 3 HP to 7-1/2 HP Totally Enclosed Fan Cooled (TEFC) Motor
• Standard 56C or JM Shaft Motors

Standard Drum Pumps

Because safety comes standard with all Standard Drum Pumps, you know you’re installing the best engineered solution.  Backed by our unmatched 3 Year Warranty, Standard Drum Pumps are the reliable choice. When you need fluid handling equipment for your chemical, industrial, water treatment or automotive application, you can have confidence in the safety, performance and reliability of Standard Drum Pumps.

ASP SPV Pumps

  • Flow Rates to 240-gpm
  • System pressures up to 125 psig
  • Impellers up to 5.75″ in diameter
  • 1/2 through 5 horsepower motors
  • Service in both 50 and 60-Hz.
  • Stainless steel casing and impellers
  • No mechanical seal
  • Custom lengths available
  • Size 1 (C1) 1.25″ NPT suction & 1.0″ NPT discharge nozzles
  • Size 2 (C2)  2.0″ NPT suction & 1.5″ NPT discharge nozzles
  • The model SPV makes our SSP/C models available as a vertical pump. The internal pump components are the same reliable parts found in our SSP/C models.
  • Our precision machined column & cast motor adapters offer a high quality stainless product at an affordable price.
  • Our extended shaft design allows for use with a standard 56J frame motor, available off the shelf in a pinch. Open impellers are available.

Request an info

Certificates & Achievements

ISO CertificationISO Certification